30A 12V/24V Solar Charge Regulator
Introduction:
LS-EU series is reliable,stable,and economical solar charge controller,easy for operation.
USB output can charge mobile phone,DC fans,and other DC electronic device.
Models:
LS0512EU 5A,12V
LS1012EU 10A,12V
LS1024EU 10A,12/24V auto work
LS2024EU 20A,12/24V auto work
LS3024EU 30A,12/24V auto work
| Model |
LS0512EU |
LS1012EU |
LS1024EU |
LS2024EU |
LS3024EU |
| Nominal system voltage |
12VDC |
12/24VDC |
| Rated battery current |
5A |
10A |
10A |
20A |
30a |
| Max. battery voltage |
8V-16V |
8V-32V |
| Max. PV open circuit voltage |
30V |
50V |
| Equalize charging voltage |
Gel: ----, Sealed: 14.6V, Flooded: 14.8V |
| Boost charging voltage |
Gel: 14.2V, Sealed: 14.4V, Flooded: 14.6V |
| Float charging voltage |
Gel / Sealed / Flooded:13.8V |
| Low voltage reconnect voltage |
Gel / Sealed / Flooded:12.6V |
| Low voltage disconnect voltage |
Gel / Sealed / Flooded:11.1V |
| USB output |
5VDC/1.2A |
5VDC/2A |
| Charge circuit voltage drop |
≤0.26V |
| Discharge circuit voltage drop |
≤0.15V |
| Self-consumption |
12V≤5mA; 24V≤7mA |
| Temp. compensation |
-5mV/°C/2V(25°C) |
| Overall dimension(mm) |
109.7x65.5x20.8 |
120.3x67x21.8 |
120.3x67x21.8 |
148x85.6x34.8 |
148x106.8x43.7 |
| Mounting dimension |
100.9mm |
111.5mm |
111.5mm |
138mm |
138mm |
| Mounting hole size |
Φ4.5 |
Φ4.5 |
Φ4.5 |
Φ4.5 |
Φ4.5 |
| Terminal |
2.5mm² |
4mm² |
4mm² |
6mm² |
10mm² |
| Weight |
95g |
103g |
102g |
179.6g |
290g |
| Working temperature |
-35ºC~+55ºC |
| Storage temperature |
-35ºC~+80ºC |
| Humidity |
≤95% N.C. |
| Enclosure |
IP20 |
Features:
1)With USBport
2)PWM charging
3)Use MOSFET as electronic switch
4)Intuitive LED indicators showing battery voltage status
5)Battery type selection: Gel, Sealed, and Flooded
6)Manual control the output of the load
7)Temperature compensation
8)Industrial grade design
Electronic protections:
1)Load overload protection
2)Load short circuit protection
3)Battery over discharge protection
4)Battery reverse polarity protection
Connection:
(1) Connect components to the charge controller in the sequence as shown below and pay much attention to the "+" and "-". Please don't insert the fuse or turn on the breaker during the installation. When disconnecting the system, the order will be reserved.
(2) After power on the controller, check the Battery LED indicator on the controller, it will be on solid green. Otherwise please refer to chapter 8. Always connect the battery first, in order to allow the controller to recognize the system voltage.
(3) The battery fuse should be installed as close to battery as possible. The suggested distance is within 150mm.
Audited Supplier 
){kind=link}
){kind=link}